When an overhead crane fails in a live plant, the first move is not diagnosis. Isolate the crane, clear and control the area beneath the load and along the bridge travel path, and confirm whether a load is suspended, because a suspended load changes every decision that follows. What failed matters second.
Type overhead crane failure what to do plant into a search bar and most of what comes back is preventive-maintenance advice written for the manager whose crane still works. This is written for the maintenance lead standing under a dead bridge crane with production waiting on it. LMM (formerly Lee Machinery Movers) takes those calls out of its Pontiac and Saginaw, MI facilities, and the pattern is consistent: plants lose the first hour to sequencing, not to the failure itself.
What do you do first when an overhead crane fails in a live plant?
When an overhead crane fails with a load suspended, the first action is not repair — it is making the load safe, de-energizing the bridge and barricading the drop zone before any diagnosis begins. What failed is the second question.
The make-safe sequence, step by step
- Move personnel back and establish an exclusion zone under and around the affected crane, including the full width of the runway.
- Confirm the load state — suspended or landed — before any other decision is made, because that single fact sets the rest of the response.
- Isolate energy and apply lockout-tagout before anyone opens a panel or puts hands on electrical components.
- Name the person who owns the outside call, with authority to approve scope on the spot.
- Document conditions — crane and trolley position, control indication, rigging in place — before anyone touches the crane.
The area is cleared and isolated before anyone works on it, and your crew works against the hazards you can identify and control. The governing framework for the equipment is already written: the crane is covered by OSHA 29 CFR 1910.179, which limits operation of a covered overhead crane to designated personnel and sets the frequent and periodic inspection intervals described later on this page, and inspection programs are built on ASME B30.2 and CMAA Specification No. 70. Make-safe is how a plant stays inside that framework while the crane is out of service.
Who owns the call when a bridge crane goes down?
Ambiguity here is where the first hour disappears. The maintenance lead makes the make-safe call. The production supervisor owns the schedule impact. One of the two has to own the outside call, and that person needs authority to approve scope on the spot. Name them before anyone picks up a phone.
Is the load in the air or on the ground?
A crane that is dead and empty is a repair problem. A crane holding a load over a live floor is a rigging problem first and a repair problem second. With a load suspended, nobody passes beneath it, nobody releases a brake to "walk it down," and the recovery becomes a planned pick with the load supported from a second source before the hoist is touched.
What actually fails on an overhead crane, and what does each failure cost you in time?
Overhead crane failures sort into three families — electrical, mechanical, and structural or alignment — and restoration time rises in that order, from frequently same-day control faults to engineered girder and runway work on a planned outage.
OSHA defines an overhead crane as a crane with a movable bridge carrying a movable or fixed hoisting mechanism and traveling on an overhead fixed runway structure, with the bridge comprising girders, trucks, end ties, footwalks and drive machinery (OSHA 29 CFR 1910.179). That structure is durable. A properly maintained bridge or gantry crane lasts at least 20 years and can reach 50 or more, according to Plant Engineering — which means most plant crane outages are component failures, not end-of-life failures. Sort them by observable symptom, then by restoration time.
| Failure family | Typical restoration path | Who to call | Production impact |
|---|---|---|---|
| Electrical — controls dead, contactors, VFD faults, festoon and runway conductors | Diagnose control transformer and contactors, read VFD fault codes before resetting, check festoon and runway conductor continuity | Repair crew; electrical support crew where temporary power is needed to keep the bay working | Control-circuit and contactor faults are frequently same-day work — the least expensive family to have |
| Mechanical — hoist brake, gearbox, wire rope and reeving, end trucks and wheels | Component replacement; restoration is parts-lead-time dependent | Crane OEM or hoist service provider supplies the parts; rigging and an operated mobile crane first if a load is suspended | Driven by parts lead time, not by labor |
| Structural and alignment — bridge girder, runway rail, skewing | Engineered repair scheduled into a planned outage | Engineered repair scope, plus mobile crane, millwrights and a lift plan if the hoist, trolley or girder must come out | Not an overnight fix — plan production around the outage rather than a hoped-for restart |
What does an electrical failure look like on a bridge crane?
Nothing responds to the pendant station or radio control. Look at control transformer and contactor condition, variable frequency drive fault codes before anyone resets them, festoon condition and runway conductor continuity. Control-circuit and contactor faults are frequently same-day work, which is why they are the least expensive family to have. Our crews carry electrical support services on our own project scopes, including temporary power when a bay has to keep working.
What are the most common mechanical failures on an overhead crane?
The hoist lowers but won't hold. The rope has jumped the reeving. Wire rope degradation — broken outer wires, birdcaging, corrosion, rope out of the sheave — and worn hoist brakes are the two problem areas reported most often across crane service literature. Restoration here is parts-lead-time dependent, and your crane OEM or hoist service provider supplies those parts.
How do you recognize a structural or alignment failure?
The bridge fights the runway, squeals, or tracks crooked. Crane skewing and runway misalignment chew through end truck wheels and rail, and they rarely announce themselves as a single failure. Girder or runway rail work is an engineered repair on a planned outage, not an overnight fix. Plan production around it rather than around a hoped-for restart.
Do you need a repair crew, a mobile crane, or both?
An overhead crane repair restores the crane; a mobile crane pick restores production — plants under an outage clock often need both, scheduled in that order.
Two different problems are on the table: restoring the asset and restoring production. Repairing the bridge crane belongs to the crane OEM or hoist service provider. Getting a suspended load down, keeping material moving while the crane is out, and removing or reinstalling the crane itself is operated-mobile-crane and rigging work.
| Load state + symptom | Bay criticality | Parts | Who you call |
|---|---|---|---|
| Crane dead, hook empty | Non-bottleneck | On hand or short lead | Repair crew only |
| Load suspended over live floor | Any | Irrelevant today | Rigging and operated mobile crane first, repair second |
| Crane dead, hook empty | Bottleneck | Lead time in days | Both, mobilized in parallel |
| Hoist, trolley or girder must come out | Any | Engineered replacement | Mobile crane, millwrights and an engineered lift plan |
Scenario 1: crane dead, no load, non-bottleneck bay
Diagnose, order parts, schedule the repair. Nothing else is warranted, and paying for a crane you don't need is not value engineering.
Scenario 2: load suspended over a live floor
The recovery pick comes first. An operated mobile crane or portable gantry takes the load, the rigging is checked and re-rigged under a plan, and the load is set down in a controlled area. Repair diagnosis starts after the hook is empty. This is the call emergency industrial support exists for.
Scenario 3: crane dead, bottleneck bay, parts on lead time
This is the one plants get wrong, because they serialize. Repair diagnosis and mobile-crane mobilization can run at the same time, and running them in parallel is usually the difference between hours and shifts of lost production. Decide in the first hour, not after the parts quote comes back.
Scenario 4: the crane itself has to come down
Removing a failed hoist, trolley or girder is a planned pick with a documented engineered critical lift plan, a ground-bearing and floor-loading check and a rigging plan. It is not an improvised lift. Reinstallation is the same discipline in reverse, which is why overhead crane installation and assembly and removal usually belong with the same crew.
When does an overhead crane failure become a rigging job?
If the failed crane was the only lifting path to the machine, the recovery is a rigging project, not a crane repair, and the two require different contractors.
The dividing line is scope. A crane OEM or hoist service provider repairs the bridge crane and supplies its parts. It does not take a suspended load off a dead hook, keep material moving through the bay while the crane is out, or remove and reinstall the hoist, trolley or girder — that work is operated mobile crane, millwright and rigging scope, executed under an engineered lift plan with ground-bearing and floor-loading checks. For a clearer breakdown of what that scope includes, see our comparison of operated crane service vs. crane rental.
LMM provides operated mobile cranes from 15 to 500 tons plus union millwright and rigging crews, so a failed-crane recovery can move from make-safe to reinstallation under one contract. Our crews are signatory with the Operating Engineers, Millwrights and Laborers, and crane service, rigging and heavy haul, millwright work and electrical support sit under that single scope rather than across three vendors.
Can a mobile crane actually work inside your building?
Often yes — and capacity is rarely the constraint. Overhead clearance, floor loading and access decide it. A machine rated far above your load can still be the wrong machine because its boom envelope or outrigger spread will not fit the bay.
Clearance governs the boom angle you can work at, and roof structure and sprinkler lines set the ceiling. Floor loading governs outrigger footprint and mat requirements, because a mobile or gantry unit carries the load down into your slab while a bridge crane carries it up into the building steel. That is why "just use a mobile crane instead" is a floor-loading question, not a capacity question. Access closes the loop: door height, aisle width, turning radius, and what has to be cleared to get the machine to the pick.
LMM operates cranes from 15 to 500 tons with NCCCO certified crane operator crews, in all terrain, rough terrain, carry deck and boom truck configurations. Carry deck is the machine that most often solves the in-plant pick. Sometimes no crane is the right answer at all: a portable gantry, jack-and-slide, or skates and rollers can move the load for less money and less disruption. Gantry cranes are a practical alternative where the plant structure cannot carry bridge loading, where the installation is temporary, or where overhead runways are long and hard to keep in alignment, per Plant Engineering. A contractor that only owns cranes will always recommend a crane.
What information do you need ready before you call for crane support?
Have the load weight and dimensions, the load's current position and height, crane capacity, span and hook height, bay clearance and floor rating, access dimensions, plant running status, and a site contact with scope authority. A prepared call collapses mobilization time.
An unprepared call spends the first hour on questions you could have answered before dialing. For an hour-by-hour view of how a same-day crane response to a plant breakdown actually unfolds, see our same-day crane service walkthrough.
Which facts determine whether a crew can be dispatched?
- Load weight and dimensions
- Current position and height of the load
- Crane capacity, span and hook height
- Overhead clearance and floor rating in the bay
- Door and aisle access dimensions
- Whether the plant is running or down
- Site contact with authority to approve scope
What should you photograph before anyone touches the crane?
Document the crane and trolley position, the pendant or control station indication, visible wire rope and hoist brake condition, and the load with its rigging in place. That record protects the incident file and shortens the responder's diagnosis.
Which site access details quietly cost hours?
Dock height, gate width and turning radius for a loaded trailer. Overhead power lines on the approach. Whether a plant escort and site-specific safety orientation are required. Union jurisdiction on the floor — our crews are signatory with the Operating Engineers, Millwrights and Laborers, which keeps that question short. Dispatch runs from the Pontiac or Saginaw facility subject to crew and equipment availability, and a response commitment you agree in advance beats an assumption every time.
Who can put an overhead crane back in service after a failure?
Return-to-service is a documented decision by a qualified person, with the failure cause understood and the corrective work recorded. A crane that failed does not go back to work simply because it moves again.
Who is allowed to authorize return to service?
OSHA 29 CFR 1910.179 permits only designated personnel to operate a covered overhead crane, and divides inspection for cranes in regular service into frequent inspections at daily-to-monthly intervals and periodic inspections at one-to-twelve-month intervals.
What inspection and load-test expectations follow a significant repair?
The same standard requires that at the beginning of each operator's shift the upper limit switch of each hoist be tried out under no load, with the block inched into the limit or run in at slow speed, and that improper operation be reported immediately to the appointed person. That single check is where normalized early warning signs get caught. Inspection programs are built on ASME B30.2 and CMAA Specification No. 70, and our crane safety inspection services are performed to the requirements of OSHA 1910.179.
Should you repair, modernize or replace the crane?
Treat it as a criticality question, not a cost question. How much of the plant stops when this crane stops? How many times has it already failed? Is the runway itself contributing to the failures? CMAA service classes D, E and F describe heavy, severe and continuous severe duty cycles, as Plant Engineering explains — a crane worked above its class will keep failing no matter how well each repair is executed.
Overhead crane failure: frequently asked questions
What should I do first when an overhead crane fails with a load suspended?
Clear and control the floor beneath and around the load, then isolate the crane and leave the load supported where it is. Do not attempt to release a brake or lower the load with a suspected hoist fault. Plan a recovery pick that takes the load from a second source before anything on the crane is disturbed.
How long does it take to get an operated mobile crane into a plant?
The timeline is driven by crew and equipment availability, distance from the Pontiac or Saginaw facility, and your plant's access and orientation requirements. Rigging is faster to mobilize than parts are to arrive, which is why parallel response beats serial response. Having your load, clearance and access dimensions ready shortens it further.
Do I need a lift plan for a one-off recovery pick?
Yes for anything non-routine, and a recovery pick is by definition non-routine. An engineered lift plan is how the pick gets reviewed before it happens rather than after.
Does the mobile crane have to be rated above the overhead crane it replaces?
Not necessarily. Capacity is rarely the constraint — overhead clearance, floor loading and access decide which machine fits, and a machine rated far above your load can still be wrong because its boom envelope or outrigger spread will not fit the bay.
Can the same contractor handle the pick and the crane removal?
Yes. Crane service, rigging and heavy haul, millwright work and electrical support sit under one contract at LMM, which is the point. Rigging and heavy haul capability plus 500+ pieces of owned equipment means the pick, the removal and the reinstall don't get split across three vendors pointing at each other.
LMM is the single accountable partner for industrial heavy equipment moving solutions, and we thrive in technically demanding environments, delivering results under tight timelines, limited access, and challenging conditions. At LMM, safety isn't just a priority — it's a way of life. If your crane is down now, or if you want the recovery pick engineered into your next planned outage instead of improvised during one, talk to our team about Michigan crane service. We also cover city-level emergency response, including emergency crane service in Saginaw, MI and metro Detroit, dispatched from our Michigan facilities.